Industrial Air Duct Cleaning in Midvale is built for plants, warehouses, and machine shops that can't shut down for a week. We pull years of dust, metal fines, and debris out of sheet metal and flexible duct runs, then verify airflow before we leave. If your crew is coughing, your filters are loading early, or your energy bill jumped, call (855) 927-7517 and we'll scope it the same day.
Industrial Air Duct Cleaning in Midvale is the mechanical removal of dust, metal fines, mold, and debris from large commercial duct systems, followed by HEPA filtration and airflow verification. It is not a shop-vac job. We isolate each run, run a negative air machine to keep contaminants out of your production floor, then work the duct with a rotary brush, air whip, and compressed air nozzle. A duct camera confirms the interior before we button it back up.
Midvale's older manufacturing stock, especially around Bingham Junction and the 700 West corridor, was built before modern filtration was standard. Sheet metal duct from that era collects dust and debris buildup fast, and flexible duct in mezzanine runs is a common spot for mold growth in ducts after a wet winter. If you've noticed restricted airflow, allergy flare-ups on the floor, or a compressor working harder than it should, a factory air duct cleaning Midvale walkthrough usually finds the cause in under an hour.
Every industrial job includes the full cleaning scope below. Add-ons like HVAC coil cleaning, HEPA filter replacement, and dryer vent fire hazard inspection are quoted separately if you want them. We tell you upfront what's covered and what isn't, so the invoice matches the quote.
Rotary brush, air whip, and compressed air nozzle work every main and branch run. Flexible duct rod reaches the long pulls. We don't skip sections because they're hard to access.
Negative air machine and HEPA vacuum run the whole job, keeping dust out of your production space. Registers get sealed before we open a panel. This is standard on every industrial job, not an upgrade.
We pull every register cover, clean behind it, and reinstall with new fasteners where needed. Diffusers get wiped down so you're not looking at dust streaks after we leave.
Open joints get sealed with duct sealant or mastic and foil tape. Leaky duct is the number one reason industrial systems lose airflow, and it's cheap to fix while we're already inside.
After cleaning, a blower door test confirms static pressure is back where it should be. You get the numbers in writing, so you can prove the work did what we said it would.
Duct camera footage of every main run, before and after. Plus a written report covering condition, repairs made, and recommended maintenance interval. That's the documentation your insurer wants.
We walk the duct layout with your facility manager, map every run, and check access panels. You get a written scope with footage counts and a flat price before we touch a tool. Most walkthroughs take 45 to 90 minutes depending on building size.
We seal registers and hang plastic containment around work zones. A negative air machine with HEPA filtration keeps dust out of your production space while we work. On occupied floors, we schedule this around your shift change so nothing stops.
Rotary brush, air whip, and compressed air nozzle break debris loose from sheet metal and flexible duct walls. A flexible duct rod reaches the long runs a brush can't. We work section by section so airflow stays balanced across the building.
A HEPA vacuum pulls everything we loosened out of the system. Then a duct camera runs the full length of each main and branch to confirm the interior is clean. If we find a missed pocket, we go back in before we close up.
We reinstall register covers, check duct sealant and foil tape at every joint, and run a blower door test to confirm static pressure is back in spec. You get before-and-after footage and a written report the same day.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Creates negative pressure inside the duct system so dust and debris can't escape into your production space. Standard setup on every occupied-building job.
Captures the debris we loosen with brushes and air tools. HEPA filtration traps particles down to 0.3 microns, which matters when your floor has food or electronics.
Mechanically scours sheet metal duct walls where dust and debris buildup is heaviest. The air whip reaches corners a brush alone can't touch.
Breaks loose packed debris in main runs and pushes it toward the extraction point. Used with containment so nothing escapes.
Documents interior condition before and after cleaning. This is how we prove the work and how you satisfy an insurance or OSHA auditor.
Reaches long horizontal and vertical runs that standard brushes can't span. Essential in older Midvale buildings with irregular duct layouts.
Measures static pressure and airflow after cleaning. It's the verification step that turns a cleaning job into a documented airflow fix.
A Bingham Junction fabrication shop had grinding dust packed into 600 feet of main duct. Static pressure was 40 percent above spec, filters loaded every three weeks, and the floor had a visible haze by mid-shift.
After a two-night industrial cleaning, static pressure returned to spec and filter changes dropped to quarterly. Duct camera footage showed clean sheet metal wall to wall. The crew stopped complaining about the haze within a week.
A Jordan Bluffs warehouse had a musty smell every morning and allergy complaints on the floor. Duct camera found mold growth in a 90-foot flexible duct run, plus heavy dust in the main.
We removed and replaced the contaminated flexible section, cleaned the main, and resealed every joint. Air quality readings came back clean and the smell was gone. The facility passed its next internal audit with no findings.
A food processing plant near Bingham Junction failed an internal air quality audit. Duct had visible debris buildup and no documentation of prior cleaning. The plant needed a fix and a paper trail fast.
We cleaned all main and branch runs overnight, delivered before-and-after duct camera footage, and provided a written report with airflow numbers. The plant passed the re-audit and set a 12-month cleaning schedule.
Most Midvale industrial duct complaints trace back to one of these four issues. We diagnose with a duct camera first, then fix the actual cause instead of just vacuuming the symptom.
Ask a pro →We mechanically clean every run with rotary brush and air whip, then HEPA-extract the debris. A blower door test confirms airflow is restored before we leave. Most Midvale shops see static pressure drop back into spec the same day.
We identify mold growth with a duct camera, contain the affected zone, and remove contaminated material. Insulation that's too far gone gets replaced. We document everything for your records and flag the moisture source so it doesn't come back.
We remove nesting material and contaminated insulation, HEPA-vac the run, and seal entry points with mastic and foil tape. If duct sections are chewed through, we replace them. You get photos of the before and after.
We measure static pressure before and after cleaning. Once the duct is clear and joints are sealed, airflow returns to design spec. Midvale facility managers typically see the energy difference within one or two billing cycles.
Most industrial jobs in Midvale run $2,400 to $18,000 in 2026, depending on duct footage, ceiling height, and contamination level. A 5,000-square-foot shop with 300 feet of main duct typically lands near the low end. A 40,000-square-foot warehouse with rooftop air handlers and mezzanine runs sits at the high end. We quote flat after a walkthrough, so the number doesn't move.
Most Midvale manufacturing and warehouse facilities should clean main duct runs every 12 to 24 months. High-particulate operations like woodworking, metal grinding, or powder coating need it every 6 to 12 months. Food processing and cold storage usually fall in the annual range. A duct camera inspection tells you definitively whether you're early or overdue.
Our standard industrial scope covers mechanical cleaning of all main and branch runs, HEPA extraction, register cover removal and reinstall, duct sealant and foil tape repair at open joints, a blower door airflow test, and before-and-after duct camera footage. Add-ons include HVAC coil cleaning, dryer vent fire hazard inspection, and HEPA filter replacement if yours are past due.
Silverline Duct handles factory air duct cleaning in Midvale, Utah from our local base, covering Salt Lake County and the surrounding industrial corridors. We're NADCA-trained, licensed, and insured, and we schedule around production shifts. Call (855) 927-7517 and we'll set a walkthrough, usually within a few business days.
Air Duct Cleaning Near MeSame industrial-grade cleaning, scheduled fast for Midvale facilities that need a crew on site this week. We map your duct layout, contain the work zone, and verify airflow before we leave. Call and we'll tell you the next open slot.Explore →
24/7 Air Duct CleaningProduction doesn't stop at 5 p.m., and neither do we. Our 24/7 crews handle overnight and weekend industrial duct cleaning in Midvale so your day shift walks into clean air. Night differential is quoted upfront.Explore →
Emergency Air Duct CleaningWhen a duct collapse, pest infestation in ducts, or mold discovery shuts down a line, we mobilize same day across Salt Lake County. Containment goes up first, then we clean and document the repair for your insurer.Explore →
Residential Air Duct CleaningThe same HEPA equipment and NADCA methods we use in factories, scaled for Midvale homes. Good for households near industrial corridors dealing with dust tracked in from outside. Most homes finish in three to four hours.Explore →Commercial Air Duct CleaningRetail, office, and restaurant duct systems across Midvale get the same containment and documentation as our industrial work. We schedule after hours so your business never closes. Flat pricing after walkthrough.Explore →
HVAC Duct CleaningDuct cleaning paired with air handler and coil inspection. If your HVAC coil is fouled, cleaning the duct alone won't fix airflow. We check both and tell you honestly what needs work.Explore →
Furnace and Duct CleaningFor Midvale shops and warehouses running gas-fired makeup air units, we clean the furnace cabinet and connected duct in one pass. Reduces dust smell on startup and keeps heat exchangers breathing.Explore →
Air Vent CleaningRegister and diffuser cleaning on industrial ceilings, including high-bay vents a ladder crew can't reach safely. We use lift equipment and contain the debris at the source.Explore →Licensed, insured, and NADCA-trained, with flat pricing after a walkthrough. Call (855) 927-7517 and we'll scope your duct system, quote it straight, and get your crew breathing clean air again.
Call (855) 927-7517 →Call (855) 927-7517 or email info@silverlineduct.com and we will get you a flat quote, usually within the hour during business hours. We run same-day and next-day slots across Midvale and Salt Lake County. If you have an after-hours emergency, the phone line stays open.